WaterBuster_072310.wmv
|
|
SHURFLO BAIT SENTRY LIVEWELL P110 Designed For Easy Installation & Trouble Free Operation $98.69 BAIT SENTRY LIVEWELL P110…. |
|
|
Attwood Self-Priming Washdown Pump $72.50 Self-priming pump for cleaning boats, general use, or use as a shower pump. Threaded male inlet and outlet for standard garden hose attachment. Pumps 4 gallons per minute, produces up to 7.5 psi pressure. Corrosion-resistant ABS housing and impeller, heavy duty 8-amp 12-volt D.C. motor…. |
|
|
Attwood Corp. 14255 LOUVERED VENT FLUSH WHITE FLUSH LOUVERED VENT $11.16 Canted louvers deflect rain and spray and help conceal the collector box. Black ABS plastic. Installs flush to the hull with #8 screws. Installation hole size: 2″ x 15-1/4″. Use with 1341 collector box for 3″ system…. |
|
|
RULE PUMPS GENERAL PURPOSE PUMP 12V Self Priming Delivers A Lot Of Water At Low Pressure 12VDC $279.69 Must be mounted below the waterline…. |
|
|
Attwood Corporation 14292-3 Livewell Aerator Switch $50.16 Attwood Livewell Aerator Switch. Keep your bait and fish alive without draining your battery! 3-position switch lets you turn it on, off or to a cycle mode. During the cycle, it will run for 30 seconds every 3 minutes. Includes face plate for panel mounting. For a 12-volt DC, 10-amp maximum only. Measures 1 1/4 x 1 1/4″. 1/2″diam. installation hole size. 3 1/4″ deep behind panel. Order yours today… |
|
|
Attwood 6143-1 2-Way Faucet/Hand Pump $84.45 ATTWOOD CORPORATION 6143-1 FAUCET/HAND PUMP 2-WAY… |
|
|
Attwood Corporation 1364A3 Cowl Ventilator $19.63 Attwood Cowl Ventilator with 3″ intake Perfect bilge Vent for house boats and more! Tough, good-looking chrome-plated die-cast Perma-Plate ZAMAK stands up to corrosion and abuse. Easy installation… comes with a flexible hose flange for secure mounting into the deck hole. Details: Measures 5 5/16 x 6 x 2 1/4″ h. Installation hole size: 3 1/4″-3 1/2″ diameter Pre-drilled with 3 holes for #8 screws… |
|
|
Attwood Tsunami Cartridge Motor – Replacement f/T1200 $25.12 Tsunami Cartridge Motor – Replacement f/T1200Part #: 4624-6This replacement cartridge motor fits the T1200 Tsunami Bilge Pump and Aerator Pump. Product : ATTWOOD TSUNAMI REPLACEMENT MOTOR CARTRIDGE F/ T1200 Manufacturer : ATTWOOD MARINE Manufacturer Part No : 4624-6 UPC : 022697462435… |
|
|
Rule Submersible Bilge Pump, 500 GPH $17.80 Rule 500 GPH Bilge Pump. Automatic and non-automatic models! A powerful Pump for smaller boats! 3/4″ discharge unit. 12V. Non-Automatic 12V: Amp draw: 1.9 amp; Fuse size: 2.5 amp; 3 1/2 x 2 3/8″; Order Now! AVAILABLE SEPARATELY: Rule Bilge Pump 500 GPH 12V Auto – word search in our Store for ‘Rule’. Rule Bilge Pump 500 GPH 12V Non-Auto… |
|
|
Attwood Sahara Automatic Pump Attwood Sahara Automatic Pump… |
|
|
Attwood 2-Way On/Off Bilge Pump Switch $13.11 2-Way On/Off Bilge Pump SwitchPart #: 7615-3Panel-mounted rocer switches for use with pump that draws 10 amps or less.Features:1/4 spade terminals6-volt through 32-volt D.C. only10 amps maximumPlate is 2-13/16 x 1-7/8 Hole size is 1-1/2 x 7/8 Caution:Bilge pump switches are not external ignition protected.Specifications:Power – Max Continuous (Amps): 10 Amps Max.Volts: 6V – 32V D.C. |
|
|
Attwood 3-Way Auto/Off/Manual Bilge Pump Switch $14.3 3-Way Auto/Off/Manual Bilge Pump SwitchPart #: 7615A3Panel-mounted rocker switches for use with pump that draws 10 amps or less. Features:1/4 spade terminals6-volt through 32-volt D.C. only10 amps maximumPlate is 2-13/16 x 1-7/8 Hole size is 1-1/2 x 7/8 Caution: Bilge pump switches are not external ignition protected.Specifications:Power – Max Continuous (Amps): 10 Amps Max.Volts: 6V – 32V D.C. |
|
|
Attwood Automatic Float Switch w/Cover – 12V & 24V $20.11 Float Switch w/CoverPart #: 4201-7Converts bilge pumps to fully automatic operation. Maximum amp draw is 12 amps (at 12-volt D.C.) or 6-amps (at 24-Volts D.C.). Features a compact, low profile design that mounts on any surface from a horizontal up to a 24 angle. Incorporates a reliable and affordable mechanical switch that actuates pump motor at 2 water level. Wire leads do not flex or hinge with the float as on some competitive models. Integral cover dampens bilge sloshing to reduce pump cycling, and prevents debris interference. Sealed switch mechanism resists moisture, fume-ignition, and electrical shock. Contains no mercury, which is listed as a health hazard and Persistent Toxic Substance in over 26 states.Float switch installs independently or directly onto the rear slots of the V-Series pump bracket. Features a convenient test knob to test pump operation.Features:36 Wire12V and 24VCE RatedIncludes CoverSpecifications:Volts: 12V & 24V |
|
|
Attwood Bilge Pump Installation Kit w/Switch, 3/4 Hose Clamps & 20′ Wire Fuse Holder $29.11 Bilge Pump Installation KitPart #: 4116-5Complete kit to install manual bilge pump with 3/4 or 1-1/8 I.D. hose outlet.Features:(1) 2-way on/off switch with bezel plate(1) 3/4 I.D. x 5′ corrugated hose(1) Thru-hull fitting for 3/4 I.D. hose(2) Snap-It hose clamps(2) 2-conductor 16-gauge wire, 20′ long(1) In-line fuse holder with two-amp fuseCaution: Bilge pump switches are not external-ignition protected.Specifications:Operation: Non-Automatic |
|
|
Attwood Bilge Switch S3 Series – 12V $26.1 Automatic Bilge Switch S3 SeriesPart #: 4801-7Incorporates a proprietary Electronic Sensing technology to detect bilge water levels and trigger pump activation and has been engineered to operate in any bilge water mixture consistently without failure. Your pump won’t be exposed to continuous cycling as the S3 switch can easily distinguish splashing bilge water, chemicals, sludge build up or foam and comes equipped with fully sealed electronics that are completely protected from water or chemical damage. For added convenience, the bilge switch can be mounted on the floor of the bilge directly to a stringer wall or alongside the basket of the pump without added components or brackets. The S3 Series switch is also directly compatible with all competitive products and free of moving parts that can jam up, break or wear out over time.Features:12V15 Amp36 Wire5-Year WarrantySpecifications:Volts: 12V |
|
|
Attwood Heavy-Duty Bilge Pump 1700 Series – 12V – 1700 GPH $67.38 Heavy-Duty Bilge Pump 1700 SeriesPart #: 4730-4Heavy-Duty Bilge Pumps integrate the highest quality bearings, brushes, alloys and magnets designed to withstand extreme usage cycles. Pump all employs an exclusive shaft and motor compartment, reducing wear and significantly extending pump life. Advanced resin compositions incorporated in exterior to resist chemicals such as engine oil, aggressive detergents and hose plasticizers. Attwood’s Heavy Duty bilge has unsurpassed durability and efficiency in a compact design to ensure electrical energy is converted to the pump rather than excess heat.The perfect upgrade from 1500 GPH rated pumps especially older and over-rated designs. Easily replaces 2000 GPH rated pumps. Delivers a true 1700 GPH at open flow while drawing less than 6-amps.Features:12VCE Rated36 Wire3-Year WarrantySpecifications:Gallons Per Hour: 1700 GPHVolts: 12V |
|
|
Attwood Heavy-Duty Bilge Pump 2000 Series – 12V – 2000 GPH $79.96 Heavy-Duty Bilge Pump 2000 SeriesPart #: 4760-4Heavy-Duty Blige Pumps integrate the highest quality bearings, brushes, alloys and magnets designed to withstand extreme usage cycles. Pump all employs an exclusive shaft and motor compartment, reducing wear and significantly extending pump life. Advanced resin compositions incorporated in exterior to resist chemicals such as engine oil, aggressive detergents and hose plasticizers. Attwood’s Heavy Duty bilge has unsurpassed durability and efficiency in a compact design to ensure electrical energy is converted to the pump rather than excess heat.Attwood’s highest capacity pump! Ball-bearing design provides for cooler motor operation and longer life, Delivers over 2000 GPH at open flow while drawing less than 7-amps.Features:12VCE Rated36 Wire3-Year WarrantySpecifications:Gallons Per Hour: 2000 GPHVolts: 12V |
|
|
Attwood Sahara Automatic Bilge Pump S1100 Series – 12V – 1100 GPH $79 Sahara Automatic Bilge Pump S1100 SeriesPart #: 4511-7An automatic-switch bilge pump is a requirement for any vessels 20′ and over with sleeping accommodations, but is a great convenience for any size boat. The Sahara has everything contained in one compact yet durable package – pump, wire seals, strainer, and mercury-free switch – and installs quickly and easily in tight spaces. Pumps include 36 lengths of 16-gauge caulked and tinned copper wire.S1100 is Attwood’s most powerful and efficient automatic pump. High capacity for larger boats and yachts. 1100 GPH at open flow, 973 GPH* at 3.3′ head. 1-1/8 hose outlet.Features:12VHose Size – 1-1/8 I.D.36 Wire3-Year WarrantySpecifications:Gallons Per Hour: 1100 GPHVolts: 12V |
|
|
Attwood Sahara Automatic Bilge Pump S750 Series – 12V – 750 GPH $67.47 Sahara Automatic Bilge Pump S750 SeriesPart #: 4507-7An automatic-switch bilge pump is a requirement for any vessels 20′ and over with sleeping accommodations, but is a great convenience for any size boat. The Sahara has everything contained in one compact yet durable package – pump, wire seals, strainer, and mercury-free switch – and installs quickly and easily in tight spaces. Pumps include 36 lengths of 16-gauge caulked and tinned copper wire.S750 is sized for larger recreational boats. Our most powerful 3/4 -outlet automatic pump. 750 GPH* at open flow, 625 GPH* at 3.3′ head. 3/4 hose outlet.Features:12V3/4 I.D.36 Wire3-Year WarrantySpecifications:Gallons Per Hour: 750 GPHVolts: 12V |
|
|
Attwood Sahara Bilge Pump – 500 G.P.H. $42.29 The Atttwood(r) Sahara bilge pump include 36-in of 16-gauge tinned copper wire. The wire is caulked to prevent water from wicking through the insulation jacket. A permanent-magnet motor, stainless-steel shaft and steel-reinforced seal assure powerful, durable performance. |
