bilge pump working but not removing water?
when i turn on my bilge pump it runs but does not remove the water. i disconnected the hose connected to the bilge pump and ran it again, and the bilge pump shoots out the water no problem. So i imagine the hose connected to it must blocked. How do i clear the hose? its a C&C 33 1985
Try to reverse flush it by blowing compressed air or water through it, have to find the outlet where the bilge pump dumps. If that doesn’t work, run a coat hanger or some wire into it and try to clear it out, then run some water/air through it. If it still doesn’t clear, remove hose and clear, or replace hose.
Installing a Drainman Extension Hose
|
|
IIT 17544 Siphon Transfer Pump Kit with 2 – 50 Inch Hoses $7.95 This siphon pump easily transfers liquids and air with minimal effort. No longer will you have to swallow half a gulp of gasoline! Two 50″ dipstick hoses attach to the pump at the center. This gives you over 8′-4″ of distance between your siphon liquid and your holding container. Common uses include oil changes, gasoline transfers, flat tire inflation and more! The included air adapter kit allows … |
|
|
T-H Marine Optima Battery Tray $15.18 T. H. Marine Battery Tray-optima 27/31. T. H. Marine Battery Tray-optima 27/31 Made by: T. H. Marine Part Number: 6033082… |
|
|
Sea Dog 426142-1 Chrome Brass Polarized Electrical Outlet $4.84 POLARIZED CABLE OUTLET is chrome brass. 12 volt, 2pin. 1-7/16 x 15/16… |
|
|
Sonin 00700 Water Alarm with Remote Sensor $10.10 Sounds an 85dB alarm when a leak is detected. Requires one 9-Volt battery. Recommended Use: Alarm, Senses: Water, Decibel Rating: 85, Power Supply: Battery, Battery Type: 9V, Battery Included: No, Compatible With: Sump and bilge pumps, Low Battery Indicator: Yes, Mount Type: Table, shelf, or wall mounted, Dimensions L x W x H (in.): 3 1/2 x 1 1/2 x 3 1/2, Single, Pair, or System: Single… |
|
|
Wel-Bilt Submersible Pump – 21.13 GPM, 1/8 HP, 1in. $39.99 Wel-Bilt Submersible Pump drains pool covers, flooded cellars and boat bilges. Maximum lift is 23ft. Screened inlet draws water from within 1/8in. of the bottom. Tough, non-corrosive polypropylene pump body. 110 Volt Motor has built-in thermal overload. Includes 1/2in., 3/4in. and 1in. hose adapters. 1in. outlet. Not for continuous use; short-duty pump only. HP: 1/8, Flow (GPH): 1,268, Volts: 110,… |
|
|
Wayne PC1 12-Volt 350 GPH Portable Battery-Powered Transfer Water Pump, Bronze $79.99 The Wayne 12-Volt 350 GPH portable battery-powered transfer water pump gets its power from car or marine batteries, with attached battery clips for easy installation and total portability. A 6-foot suction hose attachment removes water within 1/8-inch of the surface, and the pump is bronze-plated for a long life and resistance to thread damage. The discharge is threaded to attach to standard garde… |
|
|
Rule Submersible Bilge Pump, 500 GPH $17.80 Rule 500 GPH Bilge Pump. Automatic and non-automatic models! A powerful Pump for smaller boats! 3/4″ discharge unit. 12V. Non-Automatic 12V: Amp draw: 1.9 amp; Fuse size: 2.5 amp; 3 1/2 x 2 3/8″; Order Now! AVAILABLE SEPARATELY: Rule Bilge Pump 500 GPH 12V Auto – word search in our Store for ‘Rule’. Rule Bilge Pump 500 GPH 12V Non-Auto… |
|
|
Beckson 109PC Siphon-Mate Specialty Transfer Pump $25.50 Beckson Siphon-Mate Transfer Pump Safety experts caution against the unsafe practice of siphoning petroleum by mouth, warning specially, that it can result in loss of life. Beckson’s answer is the patented Siphon-Mate? pump; a combination displacement lift pump and siphon pump with valves suitable for transferring fuel. Pump half strokes to start flow. Once flow begins, fully extending the handle… |
|
|
Seattle Sports Paddlers Bilge Pump $17.99 A must for any boater, an 8-gallon per minute Bilge Pump features an easy-grab handle, super-strong pump shaft and heavy-duty impact resistant plastic…. |
|
|
PUMP BILGE 18 with 20 HOSE $20.15 BECKSON THIRSTY-MATE PUMPS are self-priming and self-lubricating. Easy to clean. Will not mar boat. Solvent welded construction. Will withstand temperature to 120°. Special all polyvinyl body and shaft. Nonconductive, noncorrosive. Has flexible hose. With seal. Made in USA. THIRSTY-MATE, 118 SERIES BILGE PUMP WITH 20″ HOSE is 18″ long, 1-1/4″ in diameter. 10 strokes per gallon. Pumps 6 gallons/mi… |
|
|
625gph Bilge Pump $30.02 Pumps water level down to 3/8 . Delivers 630 GPH at open flow, 450 GPH at 3′ head. 3/4 I.D. hose, 4.1 high, 12 volt. D.C. systems only.. |
|
|
Attwood Bilge Pump Installation Kit w/Switch, 3/4 Hose Clamps & 20′ Wire Fuse Holder $29.11 Bilge Pump Installation KitPart #: 4116-5Complete kit to install manual bilge pump with 3/4 or 1-1/8 I.D. hose outlet.Features:(1) 2-way on/off switch with bezel plate(1) 3/4 I.D. x 5′ corrugated hose(1) Thru-hull fitting for 3/4 I.D. hose(2) Snap-It hose clamps(2) 2-conductor 16-gauge wire, 20′ long(1) In-line fuse holder with two-amp fuseCaution: Bilge pump switches are not external-ignition protected.Specifications:Operation: Non-Automatic |
|
|
Attwood Heavy-Duty Bilge Pump 1700 Series – 12V – 1700 GPH $67.38 Heavy-Duty Bilge Pump 1700 SeriesPart #: 4730-4Heavy-Duty Bilge Pumps integrate the highest quality bearings, brushes, alloys and magnets designed to withstand extreme usage cycles. Pump all employs an exclusive shaft and motor compartment, reducing wear and significantly extending pump life. Advanced resin compositions incorporated in exterior to resist chemicals such as engine oil, aggressive detergents and hose plasticizers. Attwood’s Heavy Duty bilge has unsurpassed durability and efficiency in a compact design to ensure electrical energy is converted to the pump rather than excess heat.The perfect upgrade from 1500 GPH rated pumps especially older and over-rated designs. Easily replaces 2000 GPH rated pumps. Delivers a true 1700 GPH at open flow while drawing less than 6-amps.Features:12VCE Rated36 Wire3-Year WarrantySpecifications:Gallons Per Hour: 1700 GPHVolts: 12V |
|
|
Attwood Heavy-Duty Bilge Pump 2000 Series – 12V – 2000 GPH $79.96 Heavy-Duty Bilge Pump 2000 SeriesPart #: 4760-4Heavy-Duty Blige Pumps integrate the highest quality bearings, brushes, alloys and magnets designed to withstand extreme usage cycles. Pump all employs an exclusive shaft and motor compartment, reducing wear and significantly extending pump life. Advanced resin compositions incorporated in exterior to resist chemicals such as engine oil, aggressive detergents and hose plasticizers. Attwood’s Heavy Duty bilge has unsurpassed durability and efficiency in a compact design to ensure electrical energy is converted to the pump rather than excess heat.Attwood’s highest capacity pump! Ball-bearing design provides for cooler motor operation and longer life, Delivers over 2000 GPH at open flow while drawing less than 7-amps.Features:12VCE Rated36 Wire3-Year WarrantySpecifications:Gallons Per Hour: 2000 GPHVolts: 12V |
|
|
Attwood Sahara Automatic Bilge Pump S1100 Series – 12V – 1100 GPH $79 Sahara Automatic Bilge Pump S1100 SeriesPart #: 4511-7An automatic-switch bilge pump is a requirement for any vessels 20′ and over with sleeping accommodations, but is a great convenience for any size boat. The Sahara has everything contained in one compact yet durable package – pump, wire seals, strainer, and mercury-free switch – and installs quickly and easily in tight spaces. Pumps include 36 lengths of 16-gauge caulked and tinned copper wire.S1100 is Attwood’s most powerful and efficient automatic pump. High capacity for larger boats and yachts. 1100 GPH at open flow, 973 GPH* at 3.3′ head. 1-1/8 hose outlet.Features:12VHose Size – 1-1/8 I.D.36 Wire3-Year WarrantySpecifications:Gallons Per Hour: 1100 GPHVolts: 12V |
|
|
Attwood Sahara Automatic Bilge Pump S750 Series – 12V – 750 GPH $67.47 Sahara Automatic Bilge Pump S750 SeriesPart #: 4507-7An automatic-switch bilge pump is a requirement for any vessels 20′ and over with sleeping accommodations, but is a great convenience for any size boat. The Sahara has everything contained in one compact yet durable package – pump, wire seals, strainer, and mercury-free switch – and installs quickly and easily in tight spaces. Pumps include 36 lengths of 16-gauge caulked and tinned copper wire.S750 is sized for larger recreational boats. Our most powerful 3/4 -outlet automatic pump. 750 GPH* at open flow, 625 GPH* at 3.3′ head. 3/4 hose outlet.Features:12V3/4 I.D.36 Wire3-Year WarrantySpecifications:Gallons Per Hour: 750 GPHVolts: 12V |
|
|
Attwood WaterBuster Portable Pump – 200 GPH $33.64 WaterBuster Portable PumpPart #: 4140-4This patented, submersible pump is a great way to remove unwanted water from boats, pool covers, aquariums and sump pits. Convenient and safe, too, because it needs no electrical cord – runs up to 5 hours on three alkaline D batteries. Excellent for use as a portable pump-out device for paddle boats, inflatables, duck boats, dingies and kayaks. Any craft that lacks a hard-wire, permenent electrical system.Features:6-3/8 high x 5-1/4 Pumps up to 200 gallons per hourIncludes 42 hose with garden-hose adapter for adding longer hoseLifts water to height of 40Note: Not to be used as a permanent bilge pump.Specifications:Gallons Per Hour: 200 GPH |
|
|
Battery Powered Bilge Pump – Battery Powered Bile Pump/Shower $32.96 Battery Powered Bile Pump/Shower – . Manufacture ID: 1061. The Zodi self-contained portable water pump is ideal as a back-up bilge pump for any boat especially inflatable jet skis and kayaks et al. Also enjoy a comfortable shower using any water source and the included snap-in showerhead. The Battery Powered Bilge Pump & Shower is ultra convenient. Just add 4 “D” batteries and place the compact and powerful pump in any water source. A great item for emergencies smaller boats and enjoying showers on deck without lifting heavy water bags. Features:. – Powerful battery-operated pump with debris screen. – Snap-In showerhead for enjoyable showers on deck. – Simple to use by adding 4 “D” Cell batteries (not included). – 8-foot shower hose with water-conserving showerhead. – Lightweight for use anytime and anywhere |
|
|
Bilge Hose (Pump Discharge) (RBBP) $49.06 Pressure range: Not pressure rated. Maximum operating temperature: 150 F. Brittle temperature: 5 F. Material: Flexible plastic corrugated hose. Hardness: N/A. Super flexible, long lengths make some discharge jobs easier, marine applications, sump pump applications, all discharge applications where there is no vacuum. Bulk coils. No. RBBL: 3/4” I.D. x 50′ No. RBBP: 1-1/4” I.D. x 50′ |
|
|
Bilge Pump $24.87 The SeaSense submersible bilge pumps are tough enough for any bilge. The 600 GPH and 800 GPH use 3/4 hose and the 1100 GPH uses 1 1/8 hose. Meets ABYC specification H-22.. Impact Resistant ABS Housing Ignition Protected Certified Flow Rates 30 Tinned Marine Grade Wire Leads Stainless Steel Shaft & Mounting Hardware Universal Quick Release Strainer Base For Easy Cleaning Universal Mounting Hole Positions. |
